X20 Mini Excavator Rotary Brush Cutter

X20 Mini Excavator Brush Cutter - Featured 482

Videos

Images

X20 Mini Excavator Rotary Brush Cutter

Product Category: Mini Excavator

Cut up to 3″ diameter trees and clear brush faster with a 40″ cut and up to 35% faster blade speed than 36″ mini-ex cutters, all while keeping weight as low as 510 pounds.

  • NO CASE DRAIN REQUIRED. DIRECT DRIVE EATON® MOTOR WITH RELIEF VALVE PROTECTION
  • WEIGHT OPTIMIZED TO BE COMPATIBLE WITH 6500LB (3 TON) MINI EXCAVATORS
  • DECK DESIGNED TO LIMIT FLYING DEBRIS FOR SAFER OPERATION. ADD OPTIONAL SIDES FOR MAX DEBRIS CONTAINMENT
  • ROUNDED FLYWHEEL WITH 3 DOUBLE-SIDED BLADES BOUNCES OFF STUMPS. ADD OPTIONAL TEETH FOR A BETTER FINISH
  • STANDARD 90″ HOSES, COUPLERS, MOTOR GUARD & SPINDLE GUARD
  • BOLT-ON MOUNTING INTERFACE FOR QUICKLY CHANGING HANGER BRACKETS. VARIOUS HANGER BRACKETS AVAILABLE TO FIT MOST EXCAVATOR BRANDS
  • RETROFIT HYDRAULIC BRAKE KIT AVAILABLE TO REDUCE OPERATOR WAIT TIME BY STOPPING BLADE ROTATION IN LESS THAN 15 SECONDS

NOTE: Hanger bracket not included.

DO NOT OPERATE CUTTER WITHOUT A SHATTERPROOF CAB ON LOADER.

Download Spec Sheet (PDF)
Download Manual >>

No reviews have been submitted yet.

WARNING

Specs
Compare
FAQ
Downloads
Options
MODEL XB39
Cut Width (Inches) 40.1
Overall Width Without Sides / With Sides (Inches) 52.5 / 53.1
Height: Overall / Deck (Inches) 19.7 / 6.1
Overall Depth (Inches) 45.1
Minimum Cut Height (Inches) 2.3
Cutting Capacity, Diameter (Inches) 3.0
Deck Thickness: Top/Side (Inches) 3/16
Recommended Flow Rate (GPM) 13-25
Max Operating Pressure (PSI) 3500
Approximate Weight: No Sides / Both Sides (Pounds) 510¹ / 590¹
[Optional] Carbide Teeth: Weight (Pounds) / Qty 6 / 9
Approximate Operating Weight (Pounds) Cutter (510) + Hanger + Options²
Mini-Ex’s Lowest Lift Capacity Over Side at Max Reach Must Exceed Cutter Operating Weight³
Recommended Mini-Excavator Weight (Pounds) 6500-15000

¹Weight doesn’t include hanger bracket or tooth option.
²Add weight of cutter, hanger and options to determine operating weight. Hangers typically weigh between 80 and 150 pounds.
³Excavator’s lowest lift capacity of any blade and boom orientation must exceed cutter operating weight. Excavator lift capacities vary based on arm length, counterweight and open vs closed cab. Ensure the excavator configuration in the manufacturer’s specs matches your machine’s exact setup.

BLADE TIP SPEEDS (FPM)

MODEL 13 GPM 15 GPM 20 GPM 25 GPM
XB39-25 7,880 9,095 12,125 15,155

Flow rates in gallons per minute (GPM) and blade tip speeds in feet per minute (FPM).

No direct comparisons available.

Below are various questions Virnig Manufacturing receives on a regular basis. Browse through the following questions and click on a question to see the answer. If you do not see your question listed below please contact a local Virnig dealer or call 800.648.2408.

Mini Excavator Brush Cutter Frequently Asked Questions

WHICH MINI EXCAVATORS ARE VIRNIG BRUSH CUTTERS COMPATIBLE WITH?

Virnig Mini Excavator Brush Cutters are designed for mini and midi excavators. Proper machine selection requires consideration of operating weight, auxiliary hydraulic flow, and excavator lift capacity.

X20 Series (XB39, XC39-B)
The X20 Mini Excavator Brush Cutter is compatible with most mini excavators weighing between 6,500 and 15,000 pounds (3–7 tons).

X30 Series Models
The X30 Mini Excavator Brush Cutters are compatible with many mini and midi excavators weighing approximately 8,900 to 26,000 pounds.

In addition to hydraulic flow and operating weight, lift or operating capacity is critical. The excavator must be able to safely lift and control the full weight of the cutter, especially when operating over the side at full reach. If the cutter’s weight exceeds the excavator’s lift capacity at any position, unsafe operating conditions can result.

Always consult your excavator’s lift chart, operator’s manual, equipment dealer, or Virnig to verify compatibility.

CAN I USE A VIRNIG MINI EXCAVATOR BRUSH CUTTER ON A STANDARD-SIZE EXCAVATOR?

Virnig Mini Excavator Brush Cutters are specifically designed for mini and midi excavators. While some larger excavators may physically operate or connect to the attachment, these products were engineered around the hydraulic characteristics, mounting configurations, and operating requirements commonly found on mini and midi excavators.

Consult Virnig if you have questions regarding a specific machine application.

WHAT ARE THE KEY DIFFERENCES BETWEEN THE X20 & X30 CUTTERS?

X20 Series Models (XB, XC-B)
The X20 models are designed for smaller mini excavators and are ideal for less aggressive clearing applications. The deck design provides better material containment than the X30 Series without side curtains. For even more containment, add 1 or 2 side curtains.

The XB cutter uses a heavy flywheel system and high torque Eaton® motor to efficiently cut brush and trees up to approximately 3″ diameter.

X30 Series Models (XBC42, XBC48, XBC60, XC42-B, XC48-B)
X30 models are designed for more aggressive cutting applications and larger excavators.

Compared to X20 cutters, X30s provide:

  • Heavier-duty deck construction
  • Bolt-on front frame
  • More aggressive cutting geometry
  • Easier material engagement
  • Improved tree and heavy brush cutting performance
  • Ability to grub stumps

XC-B Models (Hydraulic Braking Models)
The XC-B is based on the XB and XBC platforms and includes hydraulic braking. XC-B models reduce blade stopping time to less than 15 seconds when operated in two-way auxiliary hydraulic flow mode. The hydraulic brake is intended to reduce operator wait time after hydraulic flow is disengaged.

WHAT FLOW RATE DOES MY EXCAVATOR NEED TO OPERATE A VIRNIG MINI-EX CUTTER?

The cutter’s auxiliary hydraulic flow requirements must match your excavator’s auxiliary hydraulic circuit. Virnig motors cannot handle hydraulic overflow. Operating above the recommended flow range can damage hydraulic seals, bearings, and motor components. Operating below Virnig’s recommended flow range can result in poor performance.

Important: Auxiliary hydraulic flow is the hydraulic flow available at the attachment circuit, not the excavator’s total pump flow.

39″ Models

Model Flow Range (GPM)
XB39-25 13–25
XC39-25-B 13–25
42″ Models

Model Flow Range (GPM)
XBC42-25 15–25
XBC42-28 22–28
XC42-25-B 15–25
XC42-28-B 22–28
48″ Models

Model Flow Range (GPM)
XBC48-22 15–22
XBC48-28 22–28
XBC48-35 28–35
XBC48-38 35–38
XC48-22-B 15–22
XC48-28-B 22–28
60″ Models

Model Flow Range (GPM)
XBC60-28 20–28
XBC60-35 28–35
XBC60-38 35–38
WHICH MOTOR SHOULD I CHOOSE IF MY EXCAVATOR IS IN AN OVERLAP FLOW RANGE?

Some Virnig cutter models have overlapping flow ranges, allowing operators to choose between higher blade speed or higher torque based on their application.

42″ Models (22-25 GPM Overlap)

Model Benefit
XBC42-25 / XC42-25-B Approximately 40% higher blade speed
XBC42-28 / XC42-28-B Approximately 40% higher torque

Higher blade speed typically produces cleaner cuts and improves grass and light vegetation cutting performance. Higher torque helps power through thicker brush and small trees while reducing the likelihood of stalling.

Auxiliary hydraulic flow refers to the hydraulic flow available at the attachment circuit and should not be confused with the excavator’s total hydraulic pump flow.

Important: Virnig motors cannot handle hydraulic overflow. Operating above the recommended flow range can damage hydraulic seals, bearings, motors, and other hydraulic components.

DO VIRNIG MINI EXCAVATOR BRUSH CUTTERS REQUIRE A CASE DRAIN LINE?

No. All Virnig Mini Excavator Brush Cutters are designed to operate without a case drain line.

Most mini excavators do not include a case drain connection. Eliminating the requirement simplifies installation and avoids costly machine modifications. Pressure protection is provided by the relief valve within the cutter manifold.

DO VIRNIG MINI EXCAVATOR BRUSH CUTTERS USE PISTON MOTORS?

No. Virnig Mini Excavator Brush Cutters utilize Eaton® Geroler motors.

Geroler motors have proven reliability in demanding attachment applications and offer several advantages:

  • Excellent durability
  • Better resistance to contamination
  • Less susceptibility to cavitation
  • Lower replacement cost
  • No case drain requirement

Piston motors typically require a case drain line and are generally more expensive to service and replace.

DO ALL VIRNIG MINI EXCAVATOR BRUSH CUTTERS HAVE HYDRAULIC BRAKING?

XB and XBC Virnig cutters do not include hydraulic braking. The flywheel and blades may continue for approximately 40–60 seconds after hydraulic flow is disengaged.

XC-B models include a hydraulic braking system designed to reduce blade stopping time after auxiliary hydraulic flow is disengaged.

When operated in two-way auxiliary hydraulic flow mode, blade rotation will stop in less than 15 seconds.

Hydraulic braking reduces the amount of time operators spend waiting for blade rotation to stop before exiting the machine or performing other tasks.

Regardless of the inclusion of a brake, operators must always remain in the cab and keep personnel away from the cutter until all blade rotation has completely stopped.

WHAT ARE THE BENEFITS OF THE HYDRAULIC BRAKE?

The hydraulic brake reduces blade stopping time from approximately 40–60 seconds to less than 15 seconds after hydraulic flow is disengaged.

This reduces the amount of time operators spend waiting for blade rotation to stop before:

  • Exiting the machine
  • Repositioning equipment
  • Performing inspections
  • Transitioning between work areas

Hydraulic braking is especially valuable for operators who frequently stop the cutter, regularly enter and exit the machine, or operate in rental fleet environments where convenience is important.

WHY DOES VIRNIG OFFER BOTH BRAKED AND NON-BRAKED CUTTERS?

Not every customer requires hydraulic braking. Offering both configurations allows customers to choose the solution that best fits their machine setup, application, and operating preferences.

XC-B models provide reduced blade stopping time. XB and XBC cutters provide a simpler hydraulic circuit and can operate in either one-way or two-way hydraulic configurations depending on machine setup.

Existing non-braked cutters remain fully supported and continue to operate as originally designed and intended.

WHY DIDN’T VIRNIG MINI EXCAVATOR CUTTERS HAVE HYDRAULIC BRAKING BEFORE?

During the original development of the Mini Excavator Cutter, Virnig evaluated hydraulic manifold designs that incorporated active hydraulic braking.

Testing showed that the flow-sharing characteristics common on mini excavators could negatively affect motor performance and durability when combined with conventional hydraulic braking systems.

As a result, the original production manifold design prioritized:

  • Motor protection
  • Rotational stability
  • Flywheel speed retention
  • Long-term durability

As customer expectations evolved and hydraulic brake technology continued to mature, Virnig revisited the concept and developed the current hydraulic brake system now used on XC-B models and Hydraulic Brake Kits.

CAN EXISTING VIRNIG MINI EXCAVATOR CUTTERS BE RETROFITTED WITH A HYDRAULIC BRAKE?

Some existing Virnig Mini Excavator Cutters are compatible with Hydraulic Brake Kits.

Available brake kits include:

  • XBRK1
  • XBRK2

Compatible models include:

Cutter Model Brake Kit
XB39-25 XBRK1
XBC42-25 XBRK2
XBC42-28 XBRK2
XBC48-22 XBRK2
XBC48-28 XBRK2

Contact Virnig Customer Service with the cutter model or serial number to verify compatibility.

WHAT PROTECTS THE HYDRAULIC SYSTEM FROM PRESSURE SPIKES?

A pressure relief valve protects both the cutter hydraulic motor and the excavator hydraulic system from damaging pressure spikes.

When maximum system pressure is reached, the relief valve opens to prevent pressure from increasing beyond its intended operating range.

This helps protect:

  • Hydraulic seals
  • Motors
  • Bearings
  • Internal hydraulic components
CAN I CUT BRUSH BI-DIRECTIONALLY?

No. All Virnig Mini Excavator Brush Cutters are designed to operate in the counter-clockwise direction.

Running the cutter clockwise will result in:

  • Reduced torque
  • Reduced blade speed
  • Poor cutting performance
  • Increased likelihood of stalling

For XC-B hydraulic brake models, reverse rotation produces extremely low blade tip speed and is not considered a valid operating mode.

Always verify proper rotation direction before operating the cutter.

DO VIRNIG MINI EXCAVATOR BRUSH CUTTERS REQUIRE ONE-WAY OR TWO-WAY AUXILIARY FLOW?

XB and XBC models can operate using either:

  • One-way (hammer/return-to-tank) flow OR
  • Two-way hydraulic flow

Many operators prefer one-way flow because it typically reduces return-side backpressure.

XC-B Hydraulic Brake Models
Must be operated using two-way (bi-directional) auxiliary hydraulic flow. Two-way flow is required for the hydraulic brake system to function properly.

WHAT HAPPENS IF A HYDRAULICALLY BRAKE EQUIPPED CUTTER IS OPERATED IN ONE-WAY FLOW?

The cutter will still rotate and cut material. However, the hydraulic brake will not function as intended.

Instead of actively braking when auxiliary flow is deactivated, the flywheel will free-spin or coast to a stop similarly to a non-braked cutter. Stopping time may increase from less than 15 seconds to approximately 40–60 seconds.

For proper brake operation, XC-B cutters should always be operated using two-way auxiliary hydraulic flow.

HOW DO I KNOW IF MY EXCAVATOR IS CONFIGURED FOR TWO-WAY FLOW?

Many excavators can be configured for either one-way or two-way auxiliary hydraulic flow through:

  • Selector valves
  • Diverter valves
  • Return-to-tank valves
  • Machine settings menus

Consult your excavator operator’s manual or dealer for machine-specific procedures.

For XC-B models, brake performance can also provide an indication. If the cutter is operating at full RPM and the blades stop within 15 seconds after hydraulic flow is disengaged, the brake is likely functioning properly.

If the flywheel coasts for approximately 40 seconds or longer, the machine may be configured for one-way flow or the brake system may not be functioning as intended.

WHAT IS THE MINI-EX CUTTER’S MAXIMUM OPERATING PRESSURE?

Always verify both auxiliary hydraulic flow and operating pressure before selecting a cutter. Operating the cutter above the published flow or pressure limits can damage hydraulic motors, seals, bearings, spindles, and other components. Use of the attachment outside of Virnig’s published hydraulic specifications may void warranty coverage.

3,500 PSI Models

  • XB39-25
  • XBC42-25
  • XBC42-28
  • XBC48-22
  • XBC48-28
  • XBC60-28
  • XC42-25-B
  • XC42-28-B
  • XC48-22-B
  • XC48-28-B

 
4,100 PSI Models

  • XBC48-35
  • XBC48-38
  • XBC60-35
  • XBC60-38
HOW IMPORTANT IS A QUALITY SPINDLE?

The spindle is one of the most critical and expensive performance components on a brush cutter.

Its responsibilities include:

  • Transferring power from the hydraulic motor to the flywheel
  • Maintaining smooth rotation
  • Absorbing impacts that could otherwise damage the motor

All Virnig Mini Excavator Brush Cutters utilize heavy-duty USA-made bearing spindles designed for demanding brush-clearing applications.

WHAT HANGER BRACKETS DOES VIRNIG OFFER?

Virnig offers a variety of pin-grabber and wedge-style hanger brackets designed to fit most major mini excavator brands including:

  • Kubota®
  • John Deere®
  • Bobcat®
  • CAT®
  • And many others

Hanger brackets are available with or without machined pins depending on customer requirements.

HOW DO I ORDER THE CORRECT HANGER BRACKET?

In most cases, simply provide your excavator make and model to your Virnig dealer or Virnig Customer Service. We offer hanger brackets for many popular mini excavator brands and models.

If a compatible bracket is not already available in our system, we may request the following measurements from your bucket or existing attachment:

diagram of measurements needed for hanger bracket
A: Distance between bushings
B: Distance between bushings
C: Distance between pin centers
D: Pin diameter

Common mini excavator pin diameters include 38 mm, 40 mm, 45 mm, and 50 mm.

Contact your Virnig dealer or Virnig Customer Service for assistance identifying the correct hanger bracket for your excavator.

WHAT BOLT PATTERN DO VIRNIG HANGER BRACKETS USE?

All Virnig hanger brackets utilize the six-hole Epiroc Hammer bolt pattern. This is one of the more common bolt patterns used within the excavator attachment industry.

WHAT CUTTING PERFORMANCE CAN I EXPECT?

Virnig Mini Excavator Brush Cutters utilize high torque Eaton® motors and heavy flywheel systems to maximize rotational energy and cutting performance.

The X20 Series Cutter is optimized for smaller excavators and can efficiently process brush and trees up to approximately 3″ diameter.

X30 Series models feature a heavier-duty cutter design intended for more aggressive clearing, heavier brush, and small trees.

Virnig cut capacity is the material diameter an operator can efficiently cut without becoming frustrated with productivity, reliability, or durability.

The Virnig Mini Excavator Cutter was the preferred choice over many major brands during testing, largely due to cutting performance, deck configuration options, and the ability to operate without a case drain line.

All excavators share hydraulic flow between machine functions to varying degrees. Actual cutting performance will vary based on:

  • Hydraulic flow rate
  • System pressure
  • Machine horsepower
  • Number of hydraulic pumps
  • Pump design
  • Simultaneous machine functions

Some mini excavators utilize a single hydraulic pump, meaning attachment operation, travel functions, and boom movements all compete for available hydraulic oil.

Mini excavators generally do not have the hydraulic flow and horsepower available on skid steers until approximately the 10-ton excavator size range. As a result, cutting performance may not match that of a skid steer cutter.

WHAT MATERIAL ARE THE CUTTER BLADES MADE FROM?

All Virnig cutter blades are manufactured in the USA using forged American 5160 spring steel.

The blades are heat-treated to provide:

  • High impact toughness
  • Excellent durability
  • Long service life
SHOULD I USE ZERO, ONE, OR TWO SIDE CURTAINS?

It depends on the application and material being cut.

Two Side Curtains
Using both side curtains provides maximum material containment and is recommended for:

  • Grass
  • Small brush
  • General mowing applications

One Side Curtain
Using only the left-side curtain allows larger material to exit more freely while reducing the amount of material directed toward the operator.

Most discharged material exits the front-left side of the deck.

No Side Curtains
Operating without side curtains works well for:

  • Larger-diameter material
  • Trees
  • Hedge trimming

X30 Models Only
The front cutter deck frame can also be removed when both side curtains are removed.

Removing all three bolt-on components provides the most aggressive cutting configuration.

This configuration is not intended for mowing close to the ground because keeping the blades out of dirt becomes more difficult and blade wear increases significantly.

HOW EASY IS IT TO INSTALL OR REMOVE SIDE CURTAINS?

Side curtains can be installed or removed by simply adding or removing the mounting bolts and nuts.

HOW DO I REPLACE THE CARBIDE TEETH ON THE FLYWHEEL?

To access the teeth:

  1. Remove the six bolts retaining the flywheel.
  2. Remove the flywheel.
  3. Replace the damaged teeth.
  4. Reinstall the flywheel according to the operator’s manual.

Approximate flywheel weights:

  • X20: Approximately 120 lbs
  • X30: Approximately 145 lbs or more

If only one or two teeth need replacement, it may be faster to leave the flywheel installed and use a crowfoot wrench.

Refer to the operator’s manual for more detailed procedures.

DO VIRNIG MINI EXCAVATOR BRUSH CUTTERS COME READY TO USE OFF THE PALLET?

Yes. Provided a compatible hanger bracket is installed, the cutter is ready for operation.

Standard equipment includes:

  • 90″ hydraulic hoses
  • 1/2″ hydraulic couplers

If the cutter is being installed on a long-arm excavator, the standard hose length may not be sufficient and longer hoses may be required.

For XC-B hydraulic brake models, verify the excavator is configured for two-way auxiliary hydraulic flow before operation.

Virnig Frequently Asked Questions

HOW DO I PURCHASE VIRNIG ATTACHMENTS?

Virnig sells skid steer, mini excavator, mini skid steer, compact tractor, and compact wheel loader attachments, as well as trailers, through a network of independently owned dealers. Call 800-648-2408 for assistance in finding a dealer or use the online Dealer Finder.

WHERE CAN I FIND PRICING INFORMATION?

Please contact a local Virnig dealer to obtain pricing information.

For Virnig’s suggested retail price, fill out an online Request a Quote form.

WHAT TYPE OF ATTACHMENT INTERFACE/HOOKUP DOES VIRNIG USE?

All Virnig skid steer attachments are manufactured with a universal mount to fit most skid steer loaders. The mounting frame is built to ISO 24410 and SAE J2513 standards.

All Virnig mini skid steer attachments are manufactured with a Toro®/mini universal mount, Bobcat® mount, or ASV® mount.

WHAT IS RECOMMENDED LOADER CAPACITY?

Virnig attachments are rated to provide maximum performance and protection against damage when paired with an appropriately sized loader.

Go here to find skid steer capacity and specs.

Contact a local Virnig dealer for the most accurate attachment specs, or call Virnig at 800.648.2408.

WHY DOES VIRNIG USE NITROSTEEL® CYLINDER RODS?

Virnig uses NitroSteel® rods because they are a superior performing alternative to chrome plating. The finish offers improved corrosion resistance and better grease retention.

Chrome plated cylinder rods can flake or pit and destroy the seals or other internal components; resulting in downtime and expensive repairs.

A NitroSteel® rod will perform better and increase the service life of a cylinder, making it the cost-effective choice.

WHY DOES VIRNIG MANUFACTURING USE NITROSTEEL® CYLINDER RODS?

NitroSteel® rods are a superior performing alternative to chrome plating. The finish offers improved corrosion resistance and better grease retention.

Chrome plated cylinder rods can flake or pit, causing seals to be damaged or destroyed; resulting in downtime and extensive, costly repairs.

NitroSteel® rods perform better, increase the service life of a cylinder, and are the most cost-effective choice.

WHAT IS THE SETUP TIME FOR A VIRNIG ATTACHMENT?

Most Virnig attachments are ready to work right off the pallet.

There may be specific scenarios in which additional setup time will be required. To minimize setup time, Virnig Manufacturing requires the machine brand and model to be listed in every order for attachments with hydraulic components. This ensures proper hose length, routing, and coupler sizing. In addition, all hydraulic Virnig Attachments are tested for leaks and proper operation before leaving the factory.

HOW QUICKLY CAN I GET REPLACEMENT PARTS?

Most parts for Virnig skid steer attachments are available in-stock and can be shipped as early as the same day the order is received. Fabricated and back ordered parts are available with a reasonable lead time. Virnig uses several shipping options to provide timely and cost effective delivery to customers.

Check with a local Virnig dealer for replacement part availability.

WHAT WARRANTY DOES VIRNIG OFFER?

All Virnig parts and attachments are warranted for one year from the end user’s date of purchase, or the dealer’s date of first rental/demonstration. If the warranty period has expired, a sales receipt or first rental slip will be required for warranty consideration.

The questions and answers in this FAQ are provided for general information purposes only and may not be completely accurate in every circumstance, view full details. This FAQ is subject to change without notice.

One Bolt-On Side Curtain

  • Installed on the left side to reduce debris thrown toward the operator.
one side curtain

Two Bolt-On Side Curtains

  • Completely enclose the cutter for max debris containment.
two side curtain

Carbide Teeth

  • Shred material for a better finish.
carbide teeth option

Bolt-On Hanger Bracket

  • Many options available.
  • Please contact Virnig for hanger pricing and availability.
Bolt-On Hanger Bracket