No direct comparisons available.
Efficiently mulch 6-8” diameter trees and quickly remove up to 14” diameter trees.
DIRECT DRIVE SYSTEM WITH PISTON MOTOR
Bent-axis piston motor and USA made spindle to ensure optimum performance and longevity.
BEARING & SPINDLE PROTECTION
Low-pressure relief helps prevent spindle seal failure. Spindle shaft guard prevents debris from damaging spindle seals and bearings.
FULLY-MACHINED DISC
60” disc contains no welds and is made with 1 ¼” thick, high-strength steel.
ROTATABLE, REPLACEABLE TEETH
44 Quadco® four-sided bolt-on teeth can be rotated and replaced to increase wear life. Bolt-on tooth mounts also replaceable.
RECUTTER BAR
Three deck mounted teeth and recutter bar help prevent jams, improve mulching and produce a finished look.
HEAVY-DUTY DECK
Interior deck weldments utilize, at minimum, ⅜” thick, grade 80 steel.
EASY PART REPLACEMENT
Bolt-on push bar, intake chute and discharge deflector can be replaced with ease.
TWO CHUTE STYLES
Choose from two chute styles; standard or open. See options tab for details.
Requires a high flow loader with a flow rate of 30-45 GPM. Max operating pressure is 4,200 PSI.
DO NOT OPERATE MULCHER WITHOUT A SHATTERPROOF CAB ON LOADER.
MODEL | TDM60 |
Cut Width (Inches) | 60.0 |
Overall Width (Inches) | 70.0 |
Overall Height (Inches) | 40.5 |
Overall Depth (Inches) | 77.5 |
Deck Height (Inches) | 11.0 |
Push Bar Height (Inches) | 40.5 |
Minimum Cut Height (Inches) | 2.1 |
Cutting Capacity, Diameter (Inches) | 14 |
Number of Teeth: Top / Bottom / Outside | 12 / 20 / 12 |
Maximum Disc Thickness (Inches) | 1.25 |
Deck Thickness: Top, Side / Inside (Inches) | 0.25 / 0.375¹ |
Recommended Flow Rate (GPM) | 30-45 High Flow Only |
Approximate Weight (Pounds) | 2710 |
Recommended Loader Capacity | Greater than 2800 pounds |
*Inside Deck Material is Grade 80 Plate (80,000 PSI Minimum Yield Strength).
No direct comparisons available.
Below are various questions Virnig Manufacturing receives on a regular basis. Browse through the following questions and click on a question to see the answer. If you do not see your question listed below please contact a local Virnig dealer or call 800.648.2408.
Virnig sells skid steer attachments through a network of independently owned dealers. Call 800-648-2408 for assistance in finding a dealer or use the online Dealer Finder.
Please contact a local Virnig dealer to obtain pricing information.
For Virnig’s suggested retail price, fill out an online Request a Quote form.
Virnig skid steer attachments are manufactured with a universal mount to fit most skid steer loaders. Mounting frame is built to ISO 24410 and SAE J2513 standards.
All attachments have a universal skid steer mount. Use the recommended loader capacity listed per attachment to determine if it is properly sized for the machine in question.
Virnig skid steer attachments are rated to provide maximum performance and protection from damage when used with an appropriately sized skid loader.
Go here to find skid steer capacity and specs for 2015 models.
Contact a local Virnig dealer for the most accurate specs, or contact Virnig at 800.648.2408.
Virnig uses NitroSteel® rods because they are a superior performing alternative to chrome plating. The finish offers improved corrosion resistance and better grease retention.
Chrome plated cylinder rods can flake or pit and destroy the seals or other internal components; resulting in downtime and expensive repairs.
A NitroSteel® rod will perform better and increase the service life of a cylinder, making it the cost-effective choice.
Most Virnig attachments are ready to work right off the pallet.
To minimize set up time, Virnig Manufacturing requires the machine brand and model to be listed on each order for attachments with hydraulic components to ensure proper hose length, routing, and coupler sizing. In addition, all hydraulic Virnig Attachments are tested for leaks and proper operation before leaving the factory. There may be specific scenarios in which additional setup time will be required.
Most parts for Virnig skid steer attachments are available in-stock and can be shipped as early as the same day the order is received. Fabricated and back ordered parts are available with a reasonable lead time. Virnig uses several shipping options to provide timely and cost effective delivery to customers.
Check with a local Virnig dealer for replacement part availability.
Virnig Manufacturing, Inc. products are warranted to be free from defects, in workmanship, for one year from the end user’s date of purchase.
The questions and answers in this FAQ are provided for general information purposes only and may not be completely accurate in every circumstance, view full details. This FAQ is subject to change without notice.
STANDARD CHUTE
Tapered design helps guide trees into the disc.
Bottom edge drops below the disc to scoop trees.
OPEN CHUTE
Increased space between chute and disc to process larger, bushy material.
Bottom edge flush with disc allowing work at or below grade.