The SaltSaver auger is for lighter application rates. It’s ideal if you’re focused on pretreating or want to use less salt overall. The MaxCover auger applies more material per acre, making it a better fit for deicing, higher travel speeds or when heavier coverage is needed.

Here’s a quick example when traveling at 5 mph:

• SaltSaver applies about 500 lbs/acre (bulk salt)
• MaxCover applies about 800 lbs/acre (bulk salt)

If you’re doing both pretreating and de-icing on the same job, some users recommend going with the SaltSaver. It’s more flexible, and you can always slow down ground speed slightly to increase the amount applied when needed, without changing augers.

Also, if you’re using sand instead of salt, multiply the rates by 1.25 to account for the heavier material.

The system delivers a nice, consistent spread pattern, even with heavier materials like sand or salt/sand blends. The augers with chains help keep material flowing consistently.

Yes, you have control over both. Most modern loaders allow you to adjust hydraulic flow directly from the joystick, which lets you fine-tune the spread rate and width on the fly.

From the factory, the spreader is set to throw about 15 feet to each side. Operators have reported dialing that down to as little as 4 feet using the loader’s joystick flow control, which is great for tighter spaces or when you want to reduce salt usage.

Also, you can manually adjust the flow control valve on the spreader’s hydraulic manifold. This does require tools, and it allows you to set a new baseline for both spread width and rate. Keep in mind the application rate and width adjust together. More hydraulic flow going to the motors means more material and a wider throw; less flow means less material and a narrower path.

It’s recommended to pre-treat salt with a magnesium chloride based liquid to prevent clumping and keeps salt from freezing in the totes.

They hold up extremely well and they can even be stacked two high. The poly used in the totes is a high-impact, cold-weather-rated material designed specifically for outdoor use in winter. Unlike standard plastics that can crack or get brittle in freezing temps, this poly stays tough even in subzero conditions and will never rust.

The system handles wet bulk salt well and the totes protect the salt from the elements. The dual augers with chain agitation help keep material flowing. Pre-treating salt with liquids like magnesium chloride also helps prevent freezing and keeps material flowing smoothly. However, very wet or frozen salt can cause clogs, so it’s best to avoid loading salt that’s overly wet or frozen solid. Regular maintenance and cleaning help ensure reliable operation.

Not if you take care of it with proper cleaning and maintenance. Since the salt is held in durable poly bins and spreaders away from the machine itself, it greatly reduces direct salt exposure. Like with any equipment used in winter, regular cleaning and maintenance are key to preventing corrosion and keeping your skid steer running strong season after season. If you don’t wash it regularly, you’ll have issues.

Dual spinners let you cover more ground in fewer passes and apply more material per pass. That means faster coverage and better results in less time.

With a single spinner, especially on truck salters, you often get an uneven pattern. One side might throw 15 feet, the other barely 5. This forces extra passes and overlapping to avoid missing spots.

Dual spinners throw evenly across the full width and apply twice as much salt as a single spinner. With dual spinners, you’re not guessing or doubling back, you’re done in one clean shot. More coverage. More material. Less time.

There are several big advantages:

Precision and Speed
With dual spinners, you get an even, consistent spread about 15 feet out to each side. This makes it easy to cover all areas precisely, including tight spots like carts or alleyways. Plus, you cut out a lot of drive time, sometimes saving up to an hour by not having to drive the truck back and forth. Labor is typically the largest end of year cost, so any time you save directly adds to savings.

Better Visibility and Safety
The spinners are right in front of you, so you can see exactly where the salt is going. This gives you confidence and makes it safer, especially in busy or tight areas with people and kids. Unlike trucks that spread from the back and require constant mirror checks, this spreader lets you boom in and out quickly with better visibility.

Ease of Use and Salt Savings
The totes are easy to fill and keep salt clean and dry. There’s no wasted salt. Salt savings are a huge deal in this industry, and this system helps you use only what you need, cutting down on extra c

Unlike truck salters that need to be emptied after every job, these totes can get refilled all season. Refill, spread when needed, and only need to clean out leftover salt at the end of winter.

You get faster, safer and more precise spreading, with less waste and less driving time.

Scoop-and-spread salters can be harder to fill and use. They typically only have one spinner and limited visibility while loading because you have to tip the bucket forward, making it tough to see how much salt you’re getting. It’s also harder to fill them completely. With totes, the wide-open top lets you see exactly how much salt is inside, so you can fill it 100% every time. Plus, our system uses dual spinners for better, wider spreading. Overall, it’s faster, easier, and more operator-friendly.

Virnig sells skid steer, mini excavator, mini skid steer, compact tractor, and compact wheel loader attachments, as well as trailers, through a network of independently owned dealers. Call 800-648-2408 for assistance in finding a dealer or use the online Dealer Finder.

Please contact a local Virnig dealer to obtain pricing information.

For Virnig’s suggested retail price, fill out an online Request a Quote form.

All Virnig skid steer attachments are manufactured with a universal mount to fit most skid steer loaders. The mounting frame is built to ISO 24410 and SAE J2513 standards.

All Virnig mini skid steer attachments are manufactured with a Toro®/mini universal mount, Bobcat® mount, or ASV® mount.

Virnig attachments are rated to provide maximum performance and protection against damage when paired with an appropriately sized loader.

Go here to find skid steer capacity and specs.

Contact a local Virnig dealer for the most accurate attachment specs, or call Virnig at 800.648.2408.

Virnig uses NitroSteel® rods because they are a superior performing alternative to chrome plating. The finish offers improved corrosion resistance and better grease retention.

Chrome plated cylinder rods can flake or pit and destroy the seals or other internal components; resulting in downtime and expensive repairs.

A NitroSteel® rod will perform better and increase the service life of a cylinder, making it the cost-effective choice.

NitroSteel® rods are a superior performing alternative to chrome plating. The finish offers improved corrosion resistance and better grease retention.

Chrome plated cylinder rods can flake or pit, causing seals to be damaged or destroyed; resulting in downtime and extensive, costly repairs.

NitroSteel® rods perform better, increase the service life of a cylinder, and are the most cost-effective choice.

Most Virnig attachments are ready to work right off the pallet.

There may be specific scenarios in which additional setup time will be required. To minimize setup time, Virnig Manufacturing requires the machine brand and model to be listed in every order for attachments with hydraulic components. This ensures proper hose length, routing, and coupler sizing. In addition, all hydraulic Virnig Attachments are tested for leaks and proper operation before leaving the factory.

Most parts for Virnig skid steer attachments are available in-stock and can be shipped as early as the same day the order is received. Fabricated and back ordered parts are available with a reasonable lead time. Virnig uses several shipping options to provide timely and cost effective delivery to customers.

Check with a local Virnig dealer for replacement part availability.

All Virnig parts and attachments are warranted for one year from the end user’s date of purchase, or the dealer’s date of first rental/demonstration. If the warranty period has expired, a sales receipt or first rental slip will be required for warranty consideration.