High Dump Bucket

High Dump Bucket - Extended - Featured

Videos

Images

High Dump Bucket

Product Category: Skid Steer

Increases vertical lift up to 44”, horizontal reach up to 13″ and rotates into a full 90-degree dump; ideal for loading feed mixers and dump trucks.

  • NITROSTEEL® CYLINDER RODS & TEFLON® COATED BUSHINGS ON ALL PIVOTS
  • WINDOWS FOR BETTER OPERATOR VISIBILITY
  • 3/4″ x 6″ WELD-ON EDGE

Bucket shown with optional bolt-on edge.

READ THE ULTIMATE GUIDE TO SKID STEER BUCKET ATTACHMENTS

BUCKET LOAD CALCULATOR

Download Spec Sheet (PDF)
Download Manual >>

No reviews have been submitted yet.

WARNING

Specs
Compare
FAQ
Downloads
Options
MODEL DMP60 DMP72 DMP84 DMP96
Width: Overall / Inside (Inches) 61.5 / 59.3 73.5 / 71.3 85.5 / 83.3 97.5 / 85.3
Overall Height (Inches) 29.8
Depth: Overall / Inside (Inches) 46.2 / 36.6
Window Height (Inches) 4.0
Dump Angle (Degrees) 86.0
Capacity: Struck / Heaped (Cubic Feet) 22.8 / 27.4 27.4 / 32.9 32.0 / 38.4 36.6 / 43.9
Structural Wear Bars Under Bucket (1/2″ x 4″) 3 4 4 4
Cylinder Bore / Stroke (Inches) 2.0 / 8.375
Cylinder Pins / Hinge Pins Diameter (Inches) 1.25 / 1.563
Approximate Weight (Pounds) 1015 1115 1215 1310
Recommended Loader Capacity Greater than 1800 pounds

Virnig Mfg. Inc. High Dump Bucket will increase vertical lift by approximately 44” and reach by approximately 13”. Vertical lift and reach will vary by loader.

No direct comparisons available. See similar attachments below.

Below are various questions Virnig Manufacturing receives on a regular basis. Browse through the following questions and click on a question to see the answer. If you do not see your question listed below please contact a local Virnig dealer or call 800.648.2408.

High Dump Bucket Frequently Asked Questions

WHAT WIDTH SHOULD I PURCHASE FOR THE HIGH DUMP BUCKET?

Typically, the bucket width should be larger than the width of the skid steer.

When loading material, it is possible to overload the skid steer when using a bucket that is too large. Always reference bucket recommended loader capacity before ordering. Due to the nature of design on the High Dump Bucket, there is added horizontal distance and the center of gravity will be affected when dumping out material. Caution should be used when operating to ensure safety of the operator.

If you are unsure about what width to purchase, contact a local Virnig dealer or call Virnig at 800-648-2408.

WHAT EDGE OPTIONS ARE AVAILABLE FOR THIS BUCKET?

This Virnig Bucket can be paired with a Bolt-On Edge or a Serrated Edge.

HOW DOES THE DUMP-OUT SYSTEM WORK?

The High Dump Bucket uses cylinders to rotate the skid steer bucket forward on pins, which provides approximately 44” of vertical lift and 13” of horizontal reach. The High Dump Bucket effectively allows a skid steer operator to rotate their bucket into a full 90 degree dump.

CAN I GET THE HIGH DUMP BUCKET WITHOUT VISIBILITY WINDOWS?

No, the windows for the High Dump Bucket are intentionally there for increased visibility while scooping material.

Virnig Frequently Asked Questions

HOW DO I PURCHASE VIRNIG ATTACHMENTS?

Virnig sells skid steer, mini excavator, mini skid steer, compact tractor, and compact wheel loader attachments, as well as trailers, through a network of independently owned dealers. Call 800-648-2408 for assistance in finding a dealer or use the online Dealer Finder.

WHERE CAN I FIND PRICING INFORMATION?

Please contact a local Virnig dealer to obtain pricing information.

For Virnig’s suggested retail price, fill out an online Request a Quote form.

WHAT TYPE OF ATTACHMENT INTERFACE/HOOKUP DOES VIRNIG USE?

All Virnig skid steer attachments are manufactured with a universal mount to fit most skid steer loaders. The mounting frame is built to ISO 24410 and SAE J2513 standards.

All Virnig mini skid steer attachments are manufactured with a Toro®/mini universal mount, Bobcat® mount, or ASV® mount.

WHAT IS RECOMMENDED LOADER CAPACITY?

Virnig attachments are rated to provide maximum performance and protection against damage when paired with an appropriately sized loader.

Go here to find skid steer capacity and specs.

Contact a local Virnig dealer for the most accurate attachment specs, or call Virnig at 800.648.2408.

WHY DOES VIRNIG USE NITROSTEEL® CYLINDER RODS?

Virnig uses NitroSteel® rods because they are a superior performing alternative to chrome plating. The finish offers improved corrosion resistance and better grease retention.

Chrome plated cylinder rods can flake or pit and destroy the seals or other internal components; resulting in downtime and expensive repairs.

A NitroSteel® rod will perform better and increase the service life of a cylinder, making it the cost-effective choice.

WHY DOES VIRNIG MANUFACTURING USE NITROSTEEL® CYLINDER RODS?

NitroSteel® rods are a superior performing alternative to chrome plating. The finish offers improved corrosion resistance and better grease retention.

Chrome plated cylinder rods can flake or pit, causing seals to be damaged or destroyed; resulting in downtime and extensive, costly repairs.

NitroSteel® rods perform better, increase the service life of a cylinder, and are the most cost-effective choice.

WHAT IS THE SETUP TIME FOR A VIRNIG ATTACHMENT?

Most Virnig attachments are ready to work right off the pallet.

There may be specific scenarios in which additional setup time will be required. To minimize setup time, Virnig Manufacturing requires the machine brand and model to be listed in every order for attachments with hydraulic components. This ensures proper hose length, routing, and coupler sizing. In addition, all hydraulic Virnig Attachments are tested for leaks and proper operation before leaving the factory.

HOW QUICKLY CAN I GET REPLACEMENT PARTS?

Most parts for Virnig skid steer attachments are available in-stock and can be shipped as early as the same day the order is received. Fabricated and back ordered parts are available with a reasonable lead time. Virnig uses several shipping options to provide timely and cost effective delivery to customers.

Check with a local Virnig dealer for replacement part availability.

WHAT WARRANTY DOES VIRNIG OFFER?

All Virnig parts and attachments are warranted for one year from the end user’s date of purchase, or the dealer’s date of first rental/demonstration. If the warranty period has expired, a sales receipt or first rental slip will be required for warranty consideration.

The questions and answers in this FAQ are provided for general information purposes only and may not be completely accurate in every circumstance, view full details. This FAQ is subject to change without notice.

BOLT-ON EDGE INSTALLED

  • Extends bucket edge life.
  • Reversible 5/8” x 8” bolt-on wear edge with 5/8” plow bolt holes spaced 6” on center.
  • Available on all Virnig Buckets except skeleton style, unless noted.

SERRATED BOLT-ON EDGE INSTALLED

  • Excellent alternative to toothbar for chiseling and breaking up compacted soil.
  • 3/4″ x 8″ single bevel, serrated edge with 5/8″ plow bolt holes spaced 6″ on center.
  • Available on all Virnig Buckets except skeleton style, unless noted.